The U.S. aircraft register, updated daily
FAA orders · airworthiness directive · current

86-10-11 R1: Fuel Supply Hose Assemblies

FAA order 86-10-11 R1 is an airworthiness directive in force since July 10, 1986. The FAA's subject line: Fuel Supply Hose Assemblies. It names Aerostar International Inc RX-7, Aerostar International Inc S-55, Aerostar International Inc S-60, Aerostar International Inc S-66, Aerostar International Inc S-77: about 207 aircraft on the U.S. register today across them, though an order usually covers particular versions or serial numbers rather than every one. System: other and general.

What it applies to as the FAA lists it

Kind of product
Aircraft
Makes
Aerostar International
Models
RX-6, RX-7, S-40A, S-50A, S-55A, S-60A, S-66A, S-77A, W100LB
On this site
Aerostar International Inc RX-7 96 registered
Aerostar International Inc S-55 13 registered
Aerostar International Inc S-60 81 registered
Aerostar International Inc S-66 10 registered
Aerostar International Inc S-77 7 registered

Dates and paperwork

In force since
July 10, 1986
Docket
Unknown
Status
Current
The FAA's document
Read the order on the FAA's site

The order itself the regulatory text, as published

Show the full text (2,135 characters)
86-10-11 R1 AEROSTAR (RAVEN): Amendment 39-5350. Applies to Models S-40A, S- 50A, S-55A, S-60A, S-66A, S-77A, RX-6, RX-7 and W100LB (all serial numbers) Hot Air Balloons certificated in any category. Compliance: Required prior to further flight, unless already accomplished. To preclude propane fuel leakage which could result in an uncontained fire in the balloon basket, accomplish the following: (a) Visually check all of the fuel supply hose assemblies in the balloon to determine if any are identified by the part number code "FC321-06" followed by the date of manufacture code "3Q84" or "4Q84." (b) Prior to further use, remove all hose assemblies with markings as specified in paragraph (a) of this AD, or which contain "FC321-06" part number code but no date of manufacturer code and replace with assemblies of the same part number and a date of manufacture code other than "3Q84" or "4Q84." Make the appropriate entry in the aircraft maintenance records before returning the balloon to service. (c) If the balloon does not contain any hose assemblies meeting the marking criteria specified in paragraph (a) or (b) of this AD, return the balloon to service after the appropriate entry is made in the aircraft maintenance records. NOTE: For further guidance with regard to the hose check and possible replacement required by this AD, refer to Aerostar Service Bulletin No. 120, undated. (d) An alternate method of compliance which provides an equivalent level of safety may be used if approved by the Manager, Chicago Aircraft Certification Office, FAA, 2300 East Devon Avenue, Des Plaines, Illinois 60018. All persons affected by this directive may obtain copies of the documents referred to herein upon request to Aerostar International, Inc., 1812 "E" Avenue, Sioux Falls, South Dakota 57104, or Office of the Regional Counsel, Room 1558, FAA, 601 East 12th Street, Kansas City, Missouri 64106. This amendment becomes effective on July10, 1986, to all persons except those to whom it was made immediately effective by priority letter AD issued May 21, 1986, and is identified as AD 86-10-11.

Related safety bulletins advice on the same designs, not orders

2011-07-13CE-11-44 · Fuel: Cylinder Strap Installation
2003-11-14CE-04-18 ·

Source: FAA Dynamic Regulatory System, airworthiness directives. The FAA's document is the authority; the register counts are this site's, from the FAA register of October 23, 2026. Connections as data: /graph/directive/86-10-11 R1.json · aircraft systems.